Pro-Dim Series Dimmer Controls

Pro-Dim Series Dimmers

The tough reliable solution for professional dimming.

The Pro-Dim single channel dimmers are cost effective, easy to install and come with the reliability Anytronics is renowned for worldwide.

Superbly finished and designed for complete versatility.

 

● Suitable for resistive, inductive/wound

transformer loads and most dimmable

electronic transformers for low voltage

or cold cathode lighting.

● Circuit breaker protection.

● Remote analogue input facility.

 

● Internal pre-heat control.

● Emergency lighting terminal.

● Master and slave models.

● Optional DMX 512 input on all models.

● Remote control out stations available.

● Internal maximum level control.

 

 

DUAL PRO-DIM 5

Basic

£118.00

DUAL PRO-DIM 5 Basic
Dual Channel 5A Dimming/Switching Pack
Specification:

• 5A fuse over current protection per channel

• Internal joint 0-25% Preheat control

• Setting for use with electronic ballasts

• Suitable for wall mounting, pole mounting or free standing use

• 100 W minimum load

• +10 V reference voltage output

• Dual 0-10 V analogue inputs (highest takes precedence)

• Selectable 1 second fade rate for soft start operation with large incandescent

• Push button outstations available

• Optional DMX input on XLR and RJ45 with bcd address setting

• Available as slave version

 

DUAL PRO-DIM 5

Fully Featured

 

£210.00

 
DUAL PRO-DIM 5 Fully Featured
Dual Channel 5A Dimming/Switching Pack
Specifications:

• K403 XLR DMX (16AO)

• Dual Pro-Dim 5 with DMX inputs,crossfade 2 and effects generator

• 2 channel manual dimming pack with rotary level controls

• Stand alone Crossfade 2 with speed, master, balance and crosspoint controls

• Flicker effects generator with 10 built in effects, TV, Candlelight etc. with controls for speed, min, max and flicker effects

• DMX input on XLR and RJ45 with low profile thumb wheel bcd address setting switches

• Other features same as Dual Pro-Dim 5 basic model

 

DUAL PRO-DIM 5

XFade Only

£130.00

 
DUAL PRO-DIM 5 XFade Only
Dual Channel 5A Dimming/Switching Pack with Socket Options
Specifications:

• Designed for use with both LED and incandescent star cloths

• Controls for Speed, Master level, Balance and Crosspoint

• Cycle Period 3 Hz to 82 seconds

• Master Level control 0 to 100%

• Balance 50% : 100% to 100% : 50% balance between Ch1 and Ch2

• Crosspoint full range control from mainly on alternating to off, to mainly off alternating to on

• 5A fuse over current protection per channel

• Internal joint 0-25% Preheat control

• Setting for use with electronic ballasts

• Suitable for wall mounting, pole mounting or free standing use

• Recommended minimum load 100W

 

PRO-DIM 10

Master & Slave

£98.00

 
PRO-DIM 10 Master & Slave
Single Channel 10A Dimming/Switching Pack
Specification:

• C10 circuit breaker overcurrent protection

• +10 V reference voltage output for remote potentiometer connection

• Internal 0-25% preheat control

• Setting for use with electronic ballasts

• Recommended minimum load 100 W

• Selectable 1 second fade rate for soft start operation with large incandescents

• Suitable for wall mounting, pole mounting or free standing use

• Optional emergency lighting terminal

• Push button outstations available

• Optional DMX input on XLR and RJ45 with thumbwheel bcd address setting and selectable termination resistor.

 

LOCATION PRO-DIM 10

 

£125.00

 
LOCATION PRO-DIM 10
Single Channel 10A Dimming/Switching Pack
Specifications:

• Portable 10 A dimming/switching pack with CEE form input and outputs

• Front panel C10 circuit breaker overcurrent protection

• Front panel rotary level control

• Power connected neon indicator

• Internal 0-25% preheat control

• Setting for use with electronic ballasts

• Recommended minimum load 100 W

• Selectable 1 second fade rate for soft start operation with large incandescent lamps

• Optional DMX input on XLR and RJ45 with thumbwheel bcd address setting and selectable termination resistor

 

QUAD PRO-DIM 10

£350.00

 
QUAD PRO-DIM 10
Portable Four Channel Dimming/Switching Pack
Specification:

• Portable 4 channel dimming/switching pack with CEE form input and outputs

• 10 A per channel capability with

C10 circuit breaker over current protection on each channel

• 32 A double pole isolator / circuit breaker limits total input current

• DMX input on both XLR and RJ45 in and through sockets

• Thumbwheel bcd DMX address setting and DMX data LED

• Wipe clean channel assignment panel, including marker pen

 

The Quad Pro-Dim 10 provides four channels of dimming or switching operation in a robust and portable package.

With circuit breaker protection on each channel and CEE form input and output connectors, the pack is ideal for studio,marquee or location use. The pack combines hard fired triacs with digital control technology to achieve complete dimming control with no minimum load constraints making it suitable for a wide range of dimming applications from incandescent lamps to motors and cold cathode lighting.

 

PRO-DIM 20

Master & Slave

£220.00

 
PRO-DIM 20 Master & Slave
Single Channel 20A Dimming/Switching Pack
Specifications:

• C20 circuit breaker overcurrent protection

• 60 mm slider level control (except on Slave version)

• +10 V reference voltage output for remote potentiometer connection

• Internal 0-25% preheat control

• Thermostatically controlled forced cooling

• Setting for use with electronic ballasts

• Recommended minimum load 100 W

• Selectable 1 second fade rate for soft start operation with large incandescents

• Push button outstations available

• Optional DMX input on XLR and RJ45 with thumbwheel bcd address setting and selectable termination resistor

• Output connection options :- Hardwired on internal screw terminals - CEE 17 32A input and output sockets

 

BACK

MVS HOME PAGE